丁基膠涂布機的操作方法：

Operation method of butyl rubber coating machine:

首先，準備工作：將需要涂布的鋁隔條準備好，檢查涂布機的各項參數是否正常。

Firstly, preparation work: Prepare the aluminum spacer strip that needs to be coated and check whether the various parameters of the coating machine are normal.

其次，調整設備：根據需要調整涂布機的涂布速度、壓力和溫度等參數，確保涂布質量符合要求。

Secondly, adjust the equipment: adjust the coating speed, pressure, temperature and other parameters of the coating machine as needed to ensure that the coating quality meets the requirements.

要注意的是丁基膠涂布機在常溫下呈固體形態，須經過110-150℃得高溫才能融化使用，因丁基膠導熱較慢須加熱20-30分鐘（視氣溫而定）才能完全融化，所以要求每次使用該機之前要加熱膠缸、膠頭（110-150℃下保溫）待膠融化后才能進行工作 。

It should be noted that the butyl rubber coating machine is in solid form at room temperature and needs to go through a high temperature of 110-150 ℃ before melting and use. Due to the slow thermal conductivity of butyl rubber, it needs to be heated for 20-30 minutes (depending on the temperature) to completely melt. Therefore, it is required to heat the rubber cylinder and head (kept at 110-150 ℃) before each use of the machine until the rubber melts before starting work.

然后監控涂布質量：丁基膠絕對不能出現斷膠，鋁條露白，這是影響中空玻璃壽命的關健。確保涂布的均勻性和厚度符合要求。

Then monitor the coating quality: the butyl rubber must not break or expose the aluminum strip, which is the key factor affecting the service life of the insulating glass. Ensure that the uniformity and thickness of the coating meet the requirements.

最后，完成涂布：涂布完成后，關閉涂布機的開關，清理涂布機的殘留物和廢料，保持涂布機的清潔。

Finally, complete the coating: After the coating is completed, turn off the switch of the coating machine, clean the residue and waste of the coating machine, and keep the coating machine clean.

以上就是丁基膠涂布機的操作步驟，當丁基膠涂布機處于其他位置搬運時，表面必須用柔軟的保護墊保護，然后用軟繩綁緊，用鉤子提起，平穩地移動到其他位置。在運動過程中，請注意周圍工人的安全，避免碰撞。同時保護設備不與其他物品碰撞。

The above are the operation steps of the butyl rubber coating machine. When the butyl rubber coating machine is transported to other positions, the surface must be protected with a soft protective pad, then tied tightly with a soft rope, lifted with a hook, and smoothly moved to other positions. During exercise, please pay attention to the safety of surrounding workers and avoid collisions. Simultaneously protect the device from colliding with other objects.

丁基膠粘劑涂布機概述我公司生產的丁基橡膠涂膠機采用先進技術，設計時最大限度地考慮了用戶的方便，從而大大提高了生產率和工作效率。丁基橡膠涂層是中空玻璃加工中的一個關鍵環節。只有當丁基橡膠涂層完美時，才能生產出最好的中空玻璃。為了確保間隔框架和玻璃在最佳狀態下緊密密封，應保持準確的工作溫度。

Overview of Butyl Adhesive Coating Machine Our company's butyl rubber coating machine adopts advanced technology and is designed with maximum consideration for user convenience, greatly improving productivity and work efficiency. Butyl rubber coating is a crucial step in the processing of insulating glass. Only when the butyl rubber coating is perfect can the best insulating glass be produced. To ensure that the spacing frame and glass are tightly sealed in the best condition, accurate working temperature should be maintained.

本文由丁基膠涂布機友情奉獻.更多有關的知識請點擊:http://m.yfcha.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from the butyl rubber coating machine For more information, please click: http://m.yfcha.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message